Tag Archives: helical gearbox

China wholesaler PC071 Helical Gear Combination with Nmrv Worm Gearbox Power Transmission gearbox definition

Product Description

Features
1.Made of high quality aluminium alloy gear reducer,die-cast,non-rusting,convenient to be mounted with worm gearboxes & motors as as to achieve the required speed ratio.
2.Fitting the pre-stage helical module on the main reduction unit is easily done as for any motor of type B14.
3.The PC construction is modular and therefore it can be as a separte unit mounted on any type of fitted geared motor(PAM).
Technical data
1.Four types manufactured:PC063,PC071,PC080,PC090
2.Speed ratio range:1:2.43—1:3 
3.Model: PC063/PC071/PC080/PC090
Quality control
(1) Quality guarantee: 1 year
(2) Certificate of quality: ISO9001:2000
(3)  Every product must be tested before sending
Technical performance and selection reference

Model P D D* P1
PC063 105 11 14 140(63B5)
PC071 120 14 19 160(71B5)
PC080 160 19 24/28 200(80B5)
PC090 160 24 19/28 200(90B5)

Note recommendations
To install the reduction unit it is necessary tonote the following recommendations:
1. Check the correct direction of rotation of thereduction unit output shaft before fitting the unit tothe machine.
2. Before mount with the prime moveanddevice,please check the reducers every axiadiameter, aperture,key and key slot, 
    to be theirdimensions are not deviation, and avoidassembaurtoo tight or too loose, unless it wilinfluence the reducer’s performance.
3. The mounting on the machine must be stableto avoid anv vibration.
4.Whenever possible,protect the reductiorunit against solar radiation and bad weather.
5.In the case of particularly lengthy periods ofstorage (4-6 months), if the oil seal is not immersedin the lubricant inside the unit.
   It is recommended tochange it since the rubber could stick to the shaft ormay even have lost the elasticity it needs to functionproperly.
6.Painting must definitely not go over rubberparts and the holes on the breather plugs, if any.
7.When connect with hollow or CHINAMFG shaftplease grease the joint to avoid lock or oxidation.
8.Check the correct level of the lubricantthrough the indicator, if there is one.
9. Starting must take place gradually, withoutimmediately applying the maximum load
10. Supporting unit is required when usingvarious of reducer matched with motor directiy andthe wsight of motor is a little bigger than common.
11 .Ensure the motor cools correctly byassuring good passage of air from the fan side.
12. In the case of ambient temperatures+40°C call the Technical Service.

  /* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Application: Machinery, Marine, Agricultural Machinery, Industry
Function: Speed Changing, Speed Reduction, Speed Increase
Layout: Cycloidal
Samples:
US$ 45/Piece
1 Piece(Min.Order)

|

Order Sample

Customization:
Available

|

Customized Request

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost:

Estimated freight per unit.







about shipping cost and estimated delivery time.
Payment Method:







 

Initial Payment



Full Payment
Currency: US$
Return&refunds: You can apply for a refund up to 30 days after receipt of the products.

worm gearbox

Calculating Gear Ratio in a Worm Reducer

The gear ratio in a worm reducer is determined by the number of teeth on the worm wheel (also known as the worm gear) and the number of threads on the worm shaft. The gear ratio formula for a worm reducer is:

Gear Ratio = Number of Teeth on Worm Wheel / Number of Threads on Worm Shaft

For example, if the worm wheel has 60 teeth and the worm shaft has a single thread, the gear ratio would be 60:1.

It’s important to note that worm reducers have an inherent self-locking property due to the angle of the worm threads. As a result, the gear ratio also affects the mechanical advantage and the system’s ability to resist backdriving.

When calculating the gear ratio, ensure that the worm reducer is properly designed and that the gear ratio aligns with the desired mechanical characteristics for your application. Additionally, consider factors such as efficiency, load capacity, and speed limitations when selecting a gear ratio for a worm reducer.

worm gearbox

How to Calculate the Efficiency of a Worm Gearbox

Calculating the efficiency of a worm gearbox involves determining the ratio of output power to input power. Efficiency is a measure of how well the gearbox converts input power into useful output power without losses. Here’s how to calculate it:

  • Step 1: Measure Input Power: Measure the input power (Pin) using a power meter or other suitable measuring equipment.
  • Step 2: Measure Output Power: Measure the output power (Pout) that the gearbox is delivering to the load.
  • Step 3: Calculate Efficiency: Calculate the efficiency (η) using the formula: Efficiency (η) = (Output Power / Input Power) * 100%

For example, if the input power is 1000 watts and the output power is 850 watts, the efficiency would be (850 / 1000) * 100% = 85%.

It’s important to note that efficiencies can vary based on factors such as gear design, lubrication, wear, and load conditions. The calculated efficiency provides insight into how effectively the gearbox is converting power, but it’s always a good practice to refer to manufacturer specifications for gearbox efficiency ratings.

worm gearbox

Preventing Backlash in a Worm Gearbox

Backlash in a worm gearbox can lead to reduced accuracy, positioning errors, and decreased overall efficiency. Here are steps to prevent or minimize backlash:

  • High-Quality Components: Use high-quality worm gears and worm wheels with tight manufacturing tolerances. Precision components will help reduce backlash.
  • Proper Meshing: Ensure the worm gear and worm wheel are properly aligned and meshed. Improper meshing can lead to increased backlash.
  • Preload: Applying a small amount of preload to the worm gear can help reduce backlash. However, excessive preload can increase friction and wear.
  • Anti-Backlash Mechanisms: Consider using anti-backlash mechanisms, such as spring-loaded systems or adjustable shims, to compensate for any inherent backlash.
  • Lubrication: Proper lubrication can reduce friction and play a role in minimizing backlash. Use a lubricant that provides good film strength and reduces wear.
  • Maintenance: Regularly inspect and maintain the gearbox to identify and address any changes in backlash over time.

It’s important to strike a balance between reducing backlash and maintaining smooth operation. Consulting with gearbox experts and following manufacturer guidelines will help you optimize your worm gearbox’s performance while minimizing backlash.

China wholesaler PC071 Helical Gear Combination with Nmrv Worm Gearbox Power Transmission   gearbox definition		China wholesaler PC071 Helical Gear Combination with Nmrv Worm Gearbox Power Transmission   gearbox definition
editor by CX 2024-03-26

China high quality Helical Worm 90 Degree Gearbox Right Angle Gearbox gearbox engine

Product Description

 

Product Description

Product Features

High modular design, biomimetic surface with owned intellectual property right.
Adopt German worm hob to process the worm wheel.
With the special gear geometry, it gets high torque, efficiency and long life circle.
It can achieve the direct combination for 2 sets of gearbox.
Mounting mode: foot mounted, flange mounted, torque arm mounted.
Output shaft: CHINAMFG shaft, hollow shaft.

Main applied for
Chemical industry and environmental protection
Metal processing
Building and construction
Agriculture and food
Textile and leather
Forest and paper
Car washing machinery

Detailed Photos

 

Product Parameters

Technical data:

Housing material

Cast iron/Ductile iron

Housing hardness

HBS190-240

Gear material

20CrMnTi alloy steel

Surface hardness of gears

HRC58°~62 °

Gear core hardness

HRC33~40

Input / Output shaft material

42CrMo alloy steel

Input / Output shaft hardness

HRC25~30

Machining precision of gears

accurate grinding, 6~5 Grade

Lubricating oil

GB L-CKC220-460, Shell Omala220-460

Heat treatment

tempering, cementiting, quenching, etc.

Efficiency

94%~96% (depends on the transmission stage)

Noise (MAX)

60~68dB

Temp. rise (MAX)

40°C

Temp. rise (Oil)(MAX)

50°C

Vibration

≤20µm

Backlash

≤20Arcmin

Brand of bearings

China top brand bearing, HRB/LYC/ZWZ/C&U. Or other brands requested, SKF, FAG, INA, NSK.

Brand of oil seal

CHINAMFG — ZheJiang or other brands requested

 

Our Advantages

 

 

Certifications

Packaging & Shipping

Company Profile

Xihu (West Lake) Dis.ng Transmission Equipment Co., Ltd. located HangZhou city, ZHangZhoug, as 1 professional manufacturer and exporter of cycloidal pin wheel reducer,worm reducer, gear reducer, gearbox , AC motor and relative spare parts, owns rich experience in this line for many years.

We are 1 direct factory, with advanced production equipment, the strong development team and producing capacity to offer quality products for customers.

Our products widely served to various industries of Metallurgy, Chemicals, lifting,mining,Petroleum,textile,medicine,wooden etc. Main markets: China, Africa,Australia,Vietnam, Turkey,Japan, Korea, Philippines…

Welcome to ask us any questions, good offer always for you for long term business.

FAQ

Q: Are you trading company or manufacturer?
A: We are factory.
 

Q: How long is your delivery time?
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock.
 

Q: Can we buy 1 pc of each item for quality testing?
A: Yes, we are glad to accept trial order for quality testing.

Q:How to choose a gearbox which meets your requirement?
A:You can refer to our catalogue to choose the gearbox or we can help to choose when you provide
the technical information of required output torque, output speed and motor parameter etc.

Q: What information shall we give before placing a purchase order?
A:a) Type of the gearbox, ratio, input and output type, input flange, mounting position, and motor informationetc.
b) Housing color.
c) Purchase quantity.
d) Other special requirements.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Application: Motor, Machinery, Marine, Agricultural Machinery
Hardness: Hardened Tooth Surface
Installation: 90 Degree
Layout: Coaxial
Gear Shape: Worm Gear
Step: Single-Step

worm gearbox

Common Problems and Troubleshooting for Worm Gearboxes

Worm gearboxes, like any mechanical component, can experience various issues over time. Here are some common problems that may arise and possible troubleshooting steps:

  • Overheating: Overheating can occur due to factors such as inadequate lubrication, excessive loads, or high operating temperatures. Check lubrication levels, ensure proper ventilation, and reduce loads if necessary.
  • Noise and Vibration: Excessive noise and vibration may result from misalignment, worn gears, or improper meshing. Check for misalignment, inspect gear teeth for wear, and ensure proper gear meshing.
  • Leakage: Oil leakage can be caused by damaged seals or gaskets. Inspect seals and gaskets, and replace them if necessary.
  • Reduced Efficiency: Efficiency loss can occur due to friction, wear, or misalignment. Regularly monitor gearbox performance, ensure proper lubrication, and address any wear or misalignment issues.
  • Backlash: Excessive backlash can affect precision and accuracy. Adjust gear meshing and reduce backlash to improve performance.
  • Seizure or Binding: Seizure or binding can result from inadequate lubrication, debris, or misalignment. Clean the gearbox, ensure proper lubrication, and address misalignment issues.
  • Worn Gears: Worn gear teeth can lead to poor performance. Regularly inspect gears for signs of wear, and replace worn gears as needed.
  • Seal Wear: Seals can wear over time, leading to leakage and contamination. Inspect seals regularly and replace them if necessary.

If you encounter any of these problems, it’s important to address them promptly to prevent further damage and maintain the performance of your worm gearbox. Regular maintenance, proper lubrication, and addressing issues early can help extend the lifespan and reliability of the gearbox.

worm gearbox

Materials Used for Worm Gears

Worm gears are manufactured using a variety of materials to meet different application requirements. Some commonly used materials for worm gears include:

  • Steel: Steel is a popular choice for worm gears due to its strength, durability, and wear resistance. It can handle heavy loads and is often used in industrial applications.
  • Bronze: Bronze offers good lubricity and is commonly used for the worm gear (worm) component. It provides effective wear resistance and works well in applications where quiet operation is essential.
  • Cast Iron: Cast iron is known for its high strength and durability. It’s often used for worm gears in applications where shock loads or heavy-duty conditions are expected.
  • Aluminum: Aluminum worm gears are lightweight and corrosion-resistant, making them suitable for applications where weight reduction is important.
  • Plastic: Some worm gears are made from plastic materials such as nylon or acetal. These materials are often chosen for their self-lubricating properties and quiet operation.
  • Composite Materials: Composite materials can offer a combination of properties, such as lightweight construction and corrosion resistance. They can be suitable for specific applications.

The choice of material depends on factors such as the application’s load, speed, operating environment, and required performance characteristics. It’s important to consider these factors when selecting the appropriate material for worm gears to ensure optimal performance and longevity.

worm gearbox

Preventing Backlash in a Worm Gearbox

Backlash in a worm gearbox can lead to reduced accuracy, positioning errors, and decreased overall efficiency. Here are steps to prevent or minimize backlash:

  • High-Quality Components: Use high-quality worm gears and worm wheels with tight manufacturing tolerances. Precision components will help reduce backlash.
  • Proper Meshing: Ensure the worm gear and worm wheel are properly aligned and meshed. Improper meshing can lead to increased backlash.
  • Preload: Applying a small amount of preload to the worm gear can help reduce backlash. However, excessive preload can increase friction and wear.
  • Anti-Backlash Mechanisms: Consider using anti-backlash mechanisms, such as spring-loaded systems or adjustable shims, to compensate for any inherent backlash.
  • Lubrication: Proper lubrication can reduce friction and play a role in minimizing backlash. Use a lubricant that provides good film strength and reduces wear.
  • Maintenance: Regularly inspect and maintain the gearbox to identify and address any changes in backlash over time.

It’s important to strike a balance between reducing backlash and maintaining smooth operation. Consulting with gearbox experts and following manufacturer guidelines will help you optimize your worm gearbox’s performance while minimizing backlash.

China high quality Helical Worm 90 Degree Gearbox Right Angle Gearbox   gearbox engineChina high quality Helical Worm 90 Degree Gearbox Right Angle Gearbox   gearbox engine
editor by CX 2024-03-10

China supplier CZPT S Series Worm Helical Gearbox with IEC Motor planetary gearbox

Product Description

S helical worm gearbox motor/ reducer motor

S series is 1 kind of Helical worm gearbox ,designed as Modularization and high-stainless cast iron case . It is combination of helical gear and worm gear ,which with higher efficiency and strength than simple aluminum worm gearbox . Due to their outstanding efficiency, these drives can be used in every industrial sector and tailored to individual torque and speed requirements. The gear ratios afforded by the helical-worm gear stage and the low noise levels during operation make these gear motor  ideal low-cost solutions for simple applications 

GPHQ S worm reducer motor materials 

housing material: HT2OO high-strength cast iron
Gear material: 20CrMnTi
Surface hardness of gear HRC58°-62°
Gear core hardness HRC33°-40°
Input/Output shaft material 40Cr
Input/Output shaft hardness HBS241°-286°
Shaft at oil seal position hardness HRC48 ° -55 °
Machining precision of gears material Accurate grinding 6-5 grade
Efficiency up to 98%
Noise(Max) 60-68dB
Temp.rise: 40°C
Vibration ≤20um
Motor IP54, F class ,B5 FLANGE 
color : blue  (if you need big quantity ,we can done as your wanted color )

 Our  reduction geared motor Advantage

1,reasonable price with excellent quality 
2,delivery in time 
3,safe ,reliable ,economical and durable 
4,stable transmission ,quiet operation 
5,smooth running and low noise 
6,nice appearance ,durable service life 
7,high heat-radiating efficiency ,high carrying ability 
8,each gearbox must be tested before packing
9.reply in high efficiency during 1 working day 
10. professional to produce gearbox and electric motor .

If there is any question, please don’t hesitate to contact with me (EVA), U can send us your inquiry. And you will get response in 1 working day.
 
GEARBOX CATALOGUE :
CERTIFICATION  : 

PRODUCING PROCESS:

PACKAGE : 

for 1 container, directly loading ,for less, all goods with pallet.

FAQ
1, Q:what\’s your MOQ for ac gearbox motor  ?
A: 1pc is ok for each type electric gear box  motor 

2, Q: What about your warranty for your induction speed reducer motor ?
A: 1 year ,but except man-made destroyed

3, Q: which payment way you can accept ?
A: TT, western union .

4, Q: how about your payment way ?
A: 100%payment in advanced less $5000 ,30% payment in advanced payment , 70% payment before sending over $5000.

5, Q: how about your packing of speed reduction motor  ?
A: plywood case ,if size is small  ,we will pack with pallet for less 1 container 

6, Q: What information should be given, if I buy electric helical geared motor  from you ?
A: rated power,  ratio or output speed,type ,voltage , mounting way , quantity , if more is better .

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Application: Motor, Machinery, Agricultural Machinery
Layout: Bevel
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Step: Double-Step
Motor Power: 0.18kw-22kw
Customization:
Available

|

Customized Request

worm gearbox

Can a Worm Gearbox be Used for High-Speed Applications?

Worm gearboxes are generally not recommended for high-speed applications due to their inherent design characteristics. Here’s why:

  • Efficiency: Worm gearboxes tend to have lower efficiency compared to other gearbox types, which means they can generate more heat and experience more energy loss at high speeds.
  • Heat Generation: The sliding contact between the worm and worm wheel in a worm gearbox can lead to significant friction and heat generation, especially at high speeds. This heat can cause thermal expansion, affecting the gearbox’s performance and longevity.
  • Wear and Noise: High speeds can exacerbate wear and noise issues in worm gearboxes. Increased friction and wear can lead to faster degradation of components, resulting in reduced lifespan and increased maintenance needs.
  • Backlash: Worm gearboxes may have higher backlash compared to other gearbox types, which can impact precision and accuracy in high-speed applications.

While worm gearboxes are more commonly used in applications requiring high torque and moderate speeds, they may not be the best choice for high-speed scenarios. If high-speed operation is a requirement, other gearbox types such as helical, spur, or planetary gearboxes are often better suited due to their higher efficiency, lower heat generation, and reduced wear at elevated speeds.

worm gearbox

Worm Gearbox vs. Helical Gearbox: A Comparison

Worm gearboxes and helical gearboxes are two popular types of gear systems, each with its own set of advantages and disadvantages. Let’s compare them:

Aspect Worm Gearbox Helical Gearbox
Efficiency Lower efficiency due to sliding friction between the worm and worm wheel. Higher efficiency due to rolling contact between helical gear teeth.
Torque Transmission Excellent torque transmission and high reduction ratios achievable in a single stage. Good torque transmission, but may require multiple stages for high reduction ratios.
Noise and Vibration Generally higher noise and vibration levels due to sliding action. Lower noise and vibration levels due to smoother rolling contact.
Backlash Higher inherent backlash due to the design. Lower backlash due to meshing of helical teeth.
Efficiency at Higher Speeds Less suitable for high-speed applications due to efficiency loss. More suitable for high-speed applications due to higher efficiency.
Overload Protection Natural self-locking feature provides some overload protection. May not have the same level of inherent overload protection.
Applications Commonly used for applications requiring high reduction ratios, such as conveyor systems and heavy-duty machinery. Widely used in various applications including automotive transmissions, industrial machinery, and more.

Both worm and helical gearboxes have their place in engineering, and the choice between them depends on the specific requirements of the application. Worm gearboxes are preferred for applications with high reduction ratios, while helical gearboxes are chosen for their higher efficiency and smoother operation.

worm gearbox

What Industries Commonly Use Worm Reducers?

Worm reducers are versatile mechanical components that find applications in various industries due to their unique advantages and capabilities. Some of the industries that commonly use worm reducers include:

  • Material Handling: Worm reducers are widely used in material handling equipment such as conveyors, bucket elevators, and cranes to control movement and manage heavy loads.
  • Automotive: They are utilized in automotive manufacturing processes, assembly lines, and vehicle positioning systems.
  • Food and Beverage: Worm reducers are used in food processing and packaging machinery where hygiene and cleanliness are crucial.
  • Agriculture: Agricultural equipment like irrigation systems and tractors use worm reducers for controlling rotational motion.
  • Mining and Construction: Heavy-duty applications in mining equipment, excavators, and construction machinery benefit from the torque multiplication provided by worm reducers.
  • Energy: Wind turbines and solar tracking systems use worm reducers to convert low-speed, high-torque motion into rotational energy.
  • Textile: Textile machinery employs worm reducers for controlling speed and tension in weaving and spinning operations.
  • Packaging: Packaging equipment relies on worm reducers for precise movement and positioning of packaging materials.
  • Medical: Medical devices and equipment often utilize worm reducers for their accuracy and controlled motion.
  • Printing: Printing machines use worm reducers to regulate paper feed and ensure consistent printing quality.

Worm reducers’ ability to provide high torque output, compact design, and self-locking characteristics makes them suitable for applications requiring reliable and controlled motion across various industries.

China supplier CZPT S Series Worm Helical Gearbox with IEC Motor   planetary gearbox	China supplier CZPT S Series Worm Helical Gearbox with IEC Motor   planetary gearbox
editor by CX 2024-03-08

China wholesaler Transmission Motor Unit Src Helical Worm Speed Variator Gear Reducer Gearbox planetary gearbox

Product Description

SRC HELICAL GEARBOX

Products Description

We produce speed reducers in strict accordance with ISO9001 standard to provide our customers with high quality gearboxes at competitive prices. Our gearboxes are equipped with accessories from international famous brands, such as lubricant from Shell brand, and bearing from CHINAMFG brand. The housing and gear are produced in our company under stringent quality control. All our products are available in large stocks, and we can also provide you with customized reducer solutions, pleasefeel confident to contact us.

TRC: code for gear units series

1. No code means foot-mounted

2.F: B5 flange mounted

3.Z:B14 flange mounted

Specification code of gear units 01,02.03.04

B01,MO1……means foot code,without flange

1.I.II1.B5 Output flange specification, defaultl not to write out is ok

2. IECinput flange

3.HS: Shaft input

Transmission ratio of gear units

1.M1: Mounting positio, default mounting position M1 not to write out is ok

1.No mark means without motor

2. Model motos (poles of power)voltage – frequency

voltage – frequency

 

 

HangZhou CHINAMFG Machinery Co., Ltd.

History: More than 20 years of experience in the manufacture of reducer products.Scale: Cover working area of 13300 square. meters,have more than 113 employees.
Technology: A group of professional . technical engineers and a strong R&D team.
Management: Scientific ERP management and strict quality control system.
Equipment: 50 CNC lathes,6 machining. centers, 6 gear grinding machines, 2 high-speed.hard hobbing machines, 12 gear hobbing
machines. 10 CNC cylindrical grinding machines,4 CNC internal grinding machines 1spectrometer, high-speed gear shaping 1 machine,
2 gear measuring centers 1 coordinate measuring instrument.
lnnovation: Continuously diversify products range to satisfy customers’needs.Production capacity: 1000 pcs/day.
Long-term supplier of world-class companies: t he main markets are in Southea st Asia, Europe, Middle East.
Marketing model: All export business.

 

 

 

 

Shipping Cost:

Estimated freight per unit.



To be negotiated
Application: Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car
Hardness: Hardened Tooth Surface
Step: Double-Step
Customization:
Available

|

Customized Request

worm gearbox

Is it Possible to Reverse the Direction of a Worm Gearbox?

Yes, it is possible to reverse the direction of a worm gearbox by changing the orientation of either the input or output shaft. However, reversing the direction of a worm gearbox can have some implications that need to be considered:

  • Efficiency: Reversing the direction of a worm gearbox can potentially affect its efficiency. Worm gearboxes are typically more efficient in one direction of rotation due to the design of the worm and worm wheel.
  • Backlash: Reversing the direction of rotation might lead to increased backlash or play in the gearbox, which can impact precision and smooth operation.
  • Lubrication: Depending on the gearbox’s design, reversing the direction could affect lubrication distribution and lead to uneven wear on the gear teeth.
  • Load: Reversing the direction might also impact the gearbox’s load-carrying capacity, especially if it’s designed for predominantly one-way operation.
  • Noise and Vibration: Direction reversal can sometimes result in increased noise and vibration due to changes in gear engagement and meshing behavior.

If you need to reverse the direction of a worm gearbox, it’s advisable to consult the gearbox manufacturer’s guidelines and recommendations. They can provide insights into whether the specific gearbox model is suitable for reversible operation and any precautions or adjustments needed to ensure proper functioning.

worm gearbox

Diagnosing and Fixing Oil Leakage in a Worm Gearbox

Oil leakage in a worm gearbox can lead to reduced lubrication, increased friction, and potential damage to the gearbox components. Here’s a step-by-step process to diagnose and fix oil leakage:

  1. Inspect the Gearbox: Perform a visual inspection of the gearbox to identify the source of the leakage. Check for oil stains, wet spots, or oil pooling around the gearbox.
  2. Check Seals and Gaskets: Inspect the seals, gaskets, and O-rings for any signs of wear, cracks, or damage. These components are common points of leakage.
  3. Tighten Bolts and Fasteners: Ensure that all bolts, screws, and fasteners are properly tightened. Loose fasteners can create gaps that allow oil to escape.
  4. Replace Damaged Seals: If you find damaged seals or gaskets, replace them with new ones. Use seals that are compatible with the operating conditions and lubricant.
  5. Check Breather Vent: A clogged or malfunctioning breather vent can cause pressure buildup inside the gearbox, leading to leakage. Clean or replace the breather vent if necessary.
  6. Examine Shaft Seals: Check the shaft seals for wear or damage. If they’re worn out, replace them with seals of the appropriate size and material.
  7. Use Proper Lubricant: Ensure that you’re using the correct lubricant recommended for the gearbox. Using the wrong type of lubricant can cause leaks.
  8. Apply Sealants: In some cases, applying a suitable sealant to the joints and connections can help prevent leaks. Follow the manufacturer’s instructions for proper application.
  9. Monitor Leakage: After addressing the issues, monitor the gearbox for any signs of continued leakage. If leakage persists, further investigation may be required.
  10. Regular Maintenance: Implement a regular maintenance schedule that includes checking seals, gaskets, and other potential leakage points. Timely maintenance can prevent future leakage issues.

If you’re unsure about diagnosing or fixing oil leakage in a worm gearbox, consider consulting with a professional or gearbox manufacturer to ensure proper resolution.

worm gearbox

Lubrication Requirements for a Worm Gearbox

Lubrication is crucial for maintaining the performance and longevity of a worm gearbox. Here are the key considerations for lubricating a worm gearbox:

  • Type of Lubricant: Use a high-quality, high-viscosity lubricant specifically designed for worm gearboxes. Worm gearboxes require lubricants with additives that provide proper lubrication and prevent wear.
  • Lubrication Interval: Follow the manufacturer’s recommendations for lubrication intervals. Regularly check the gearbox’s temperature and oil condition to determine the optimal frequency of lubrication.
  • Oil Level: Maintain the proper oil level to ensure effective lubrication. Too little oil can lead to insufficient lubrication, while too much oil can cause overheating and foaming.
  • Lubrication Points: Identify all the lubrication points on the gearbox, including the worm and wheel gear surfaces. Apply the lubricant evenly to ensure complete coverage.
  • Temperature: Consider the operating temperature of the gearbox. Some lubricants have temperature limits, and extreme temperatures can affect lubricant viscosity and performance.
  • Cleanliness: Keep the gearbox and the surrounding area clean to prevent contaminants from entering the lubricant. Use proper filtration and seals to maintain a clean environment.
  • Monitoring: Regularly monitor the gearbox’s temperature, noise level, and vibration to detect any signs of inadequate lubrication or other issues.

Proper lubrication will reduce friction, wear, and heat generation, ensuring smooth and efficient operation of the worm gearbox. Always refer to the manufacturer’s guidelines for lubrication specifications and intervals.

China wholesaler Transmission Motor Unit Src Helical Worm Speed Variator Gear Reducer Gearbox   planetary gearbox	China wholesaler Transmission Motor Unit Src Helical Worm Speed Variator Gear Reducer Gearbox   planetary gearbox
editor by CX 2023-09-26

China best Helical Worm Gearbox with Hollow Output Shaft cycloidal gearbox

Product Description

Company  Profiles

     
-We are a leading gear motor manufacturer
ZHangZhoug Xihu (West Lake) Dis.hai Reducer is a leading manufacturer of gear motor and gearbox.
Since 1991, we have specialized in manufacturing a wide range of gear motor and gear box including:
 

 

  • helical gear motor
  • helical bevel gear motor
  • parallel shaft helical gear motor
  • helical worm gear motor
  • hoist drive
  • heavy-duty helical gearbox
  • heavy-duty helical bevel gearbox
  • gear motor for car parking system
  • sprial bevel gearbox

Product Description
 

E series gear motor is combined with helical gear and worm gear. It is 90° for input and output shaft.

Mounting position: footed mounting, flange mounting and shaft mounting etc.

Technical data:

Output speed:0.12~397rpm

Rated output torque:10~4200N*m

Motor power: 0.12~22KW

Product Show

Product Specification

 

Product features
1. Economical operation, low noise and high permitted overhung loads.
2. Due to their outstanding efficiency, these drives can be used in every industrial sector and tailored to individual torque and speed requirements.
General Technical data
Housing material HT250 high-strength cast iron
Housing hardness HBS190-240
Pinion material  20CrMnTiH
Gear material 20CrMnTiH
Surface hardness of gears HRC58°~62 °
Gear core hardness HRC33~40
Input /output shaft material 40CrMnTiH
Input / Output shaft hardness HRC25~30
Machining precision of gears accurate grinding, 6~7 Grade
Lubricating oil GB L-CKC220
Heat treatment tempering, cementiting, quenching, etc.
Efficiency 94%~96% (depends on the transmission stage) 
Noise (MAX) 60~68dB
Temp. rise  (MAX) 40°C 
Temp. rise (Oil)(MAX) 50°C
Vibration ≤20µm
Backlash ≤20Arcmin
Brand of bearings China Top brand C&U,LYC,TMB or other brands requested, SKF…..
Brand of oil seal CTY— ZheJiang or other brands requested
E —- series helical-worm gear motor
E-series single stages
Model Output Shaft Dia. Center Height Output Flange Dia. Power Ratio Permitted Torque Output Speed 
Solid (mm)  (mm) (mm) (kw) (Nm) (RPM)
E37 20k6 80j6 80/120 0.12~1.5 6.72~160 105 8.4~397
E47 25k6 100j6 110/160 0.12~1.5 7.5~212 190 6.6~192
E57 30k6 112j6 130/200 0.18~3.0 7.5~212 340 6.5~194
E67 35k6 140j6 130/200 0.25~5.5 7.45~215 565 6~189
E77 45k6 180j6 180/250 0.37~7.5 7.9~257 1200 3.5~177
E87 60m6 225h6 250/350 0.55~15 8.52~277 2600 1.0~171
E97 70m6 280h6 350/450 1.5~22 8.26~282 4185 4.9~177
E- series double stages 
Model Output Shaft Dia. Center Height Output Flange Dia. Power Ratio Permitted Torque Output Speed 
Solid (mm)  (mm) (mm) (kw) (Nm) (RPM)
E37D17 20k6 80j13 80/120 0.12 110~202 89 6.8~13
E47D17 25k6 100j13 110/160 0.12~0.18 180~438 255 3.2~7.4
E57D17 30k6 112j13 130/200 0.12~0.25 131~655 311 2.1~9.9
E67D37 35k6 140j13 130/200 0.12~0.37 246~1363 600 1.0~5.6
E77D37 45k6 180j13 180/250 0.12~1.1 219~3540 1230 0.39~6.4
E87D57 60m6 225h13 250/350 0.12~1.5 205~7643 2810 0.18~6.9
E97D57 70m6 280h13 350/450 0.12~3.0 179~11267 4420 0.12~7.7
Remarks: please refer to our catalogue or ask for sales man when your technical requirements is    special.

Package

Plastic bag + wooden carton

Certificate

FAQ

Q: Can you print other colors?
Yes. Customized color can be printed on the gear motor according to your requirements.
Q: Is that factory price?
Yes. We assure you all prices are based on factory.
Q:  What is the life span? what is the guarantee
The lifespan of gear motor can reach 5-20 years depending on different working conditions .The guarantee time is 1 year after delivery.
Q: What documents are available?
A full range documents including structural drawings, packing list, installation manual and relative certificates can be provided. Moreover, customs declaration is provided. We provide one-stop service for you. 
Q: Is it able to customized?
yes, we could re-design and produce the gear motor as your requirements if the quantity is large.

Application: Motor, Machinery, Transmission Equipment
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Layout: Shunting
Gear Shape: Bevel
Step: Three-Step

How to Calculate the Efficiency of a Worm Gearbox

Calculating the efficiency of a worm gearbox involves determining the ratio of output power to input power. Efficiency is a measure of how well the gearbox converts input power into useful output power without losses. Here’s how to calculate it:

  • Step 1: Measure Input Power: Measure the input power (Pin) using a power meter or other suitable measuring equipment.
  • Step 2: Measure Output Power: Measure the output power (Pout) that the gearbox is delivering to the load.
  • Step 3: Calculate Efficiency: Calculate the efficiency (η) using the formula: Efficiency (η) = (Output Power / Input Power) * 100%

For example, if the input power is 1000 watts and the output power is 850 watts, the efficiency would be (850 / 1000) * 100% = 85%.

It’s important to note that efficiencies can vary based on factors such as gear design, lubrication, wear, and load conditions. The calculated efficiency provides insight into how effectively the gearbox is converting power, but it’s always a good practice to refer to manufacturer specifications for gearbox efficiency ratings.

Customization:
Available

|

Customized Request

What Industries Commonly Use Worm Reducers?

Worm reducers are versatile mechanical compone

Common Problems and Troubleshooting for Worm Gearboxes

Worm gearboxes, like any mechanical component, can experience various issues over time. Here are some common problems that may arise and possible troubleshooting steps:

  • Overheating: Overheating can occur due to factors such as inadequate lubrication, excessive loads, or high operating temperatures. Check lubrication levels, ensure proper ventilation, and reduce loads if necessary.
  • Noise and Vibration: Excessive noise and vibration may result from misalignment, worn gears, or improper meshing. Check for misalignment, inspect gear teeth for wear, and ensure proper gear meshing.
  • Leakage: Oil leakage can be caused by damaged seals or gaskets. Inspect seals and gaskets, and replace them if necessary.
  • Reduced Efficiency: Efficiency loss can occur due to friction, wear, or misalignment. Regularly monitor gearbox performance, ensure proper lubrication, and address any wear or misalignment issues.
  • Backlash: Excessive backlash can affect precision and accuracy. Adjust gear meshing and reduce backlash to improve performance.
  • Seizure or Binding: Seizure or binding can result from inadequate lubrication, debris, or misalignment. Clean the gearbox, ensure proper lubrication, and address misalignment issues.
  • Worn Gears: Worn gear teeth can lead to poor performance. Regularly inspect gears for signs of wear, and replace worn gears as needed.
  • Seal Wear: Seals can wear over time, leading to leakage and contamination. Inspect seals regularly and replace them if necessary.

If you encounter any of these problems, it’s important to address them promptly to prevent further damage and maintain the performance of your worm gearbox. Regular maintenance, proper lubrication, and addressing issues early can help extend the lifespan and reliability of the gearbox.

nts that find applications in various industries due to their unique advantages and capabilities. Some of the industries that commonly use worm reducers include:

  • Material Handling: Worm reducers are widely used in material handling equipment such as conveyors, bucket elevators, and cranes to control movement and manage heavy loads.
  • Automotive: They are utilized in automotive manufacturing processes, assembly lines, and vehicle positioning systems.
  • Food and Beverage: Worm reducers are used in food processing and packaging machinery where hygiene and cleanliness are crucial.
  • Agriculture: Agricultural equipment like irrigation systems and tractors use worm reducers for controlling rotational motion.
  • Mining and Construction: Heavy-duty applications in mining equipment, excavators, and construction machinery benefit from the torque multiplication provided by worm reducers.
  • Energy: Wind turbines and solar tracking systems use worm reducers to convert low-speed, high-torque motion into rotational energy.
  • Textile: Textile machinery employs worm reducers for controlling speed and tension in weaving and spinning operations.
  • Packaging: Packaging equipment relies on worm reducers for precise movement and positioning of packaging materials.
  • Medical: Medical devices and equipment often utilize worm reducers for their accuracy and controlled motion.
  • Printing: Printing machines use worm reducers to regulate paper feed and ensure consistent printing quality.

Worm reducers’ ability to provide high torque output, compact design, and self-locking characteristics makes them suitable for applications requiring reliable and controlled motion across various industries.

China best Helical Worm Gearbox with Hollow Output Shaft   cycloidal gearbox	China best Helical Worm Gearbox with Hollow Output Shaft   cycloidal gearbox
editor by CX 2023-08-14

China 150 ratio speed reducer gearbox helical worm geared motors s series speed reducer gear box assembly with reducer gear box aluminum worm gearbox

Guarantee: 1 yr
Relevant Industries: Creating Substance Outlets, Producing Plant, Machinery Fix Stores, Food & Beverage Manufacturing unit, Farms, Retail, Building works , Strength & Mining, Other
Excess weight (KG): 1 KG
Customized assistance: OEM, ODM
Gearing Arrangement: Helical
Output Torque: 1400N.m, 180N.m~17000N.m
Input Pace: 1500, 1400, 900, 500rpm
Output Speed: seventy five, twenty five~300rpm
Solution identify: helical worm geared motors s sequence velocity reducer equipment box assembly
Ratio: 5 7 10 twelve.5
Mounting Position: Torque Arm Mounted
Enter Form: Keyed CZPT Shaft Input
Output Sort: Keyed Hollow Shaft Output
Application: conveyor technique
Color: Buyer Necessity
Packaging Specifics: Wooden box
Port: HangZhou,ZheJiang ,HangZhou,ZheJiang G

TA Shaft Mounted ReducerOutput Shaft Bore [mm]Ratio(i)Rated torque
KTA30Φ307.ten,twelve.5180N.m
KTA35Φ355,ten,fifteen,twenty,25420N.m
KTA40Φ405,ten,12.5,15.twenty,25900N.m
Φ45
KTA45Φ455,ten,twelve.5,15.twenty,25UOON.m
Φ50
Φ55
KTA50Φ505, Higher Quality snake spring horizontal set up forty five# metal grid coupling metal adaptable shaft connector serpentine spring 10,twelve.5,fifteen,20,252300N.m
Φ55
Φ60
KTA60Φ605,10,12.5,fifteen,twenty,253600N.m
Φ70
KTA70Φ705,10,125,15,twenty,twenty five,315100N.m
Φ85
KTA80Φ805,ten,12.5,fifteen,20,25,317000N.m
Φ100
KTA100Φ1005,10,12.5,fifteen,twenty,twenty five,3111000N.m
Φ125
KTA125Φ1255, Coupling Manufacturer Z20-60110 keyless shaft locking device Factory Cost 45# metal cam assembly energy locks adjustable 10,12.5,15.20,twenty five,3117000N.m
Φ135
SMR Model NO.Ouipui Shaft Bore [mm]Ratio(i)
StandardAlternative5:113:120:1
BΦ30Φ40
CΦ40Φ50
DΦ50Φ55
EΦ55Φ65
FΦ65Φ75
GΦ75Φ85
HΦ85Φ100
JΦ100Φ120
Exporting to Saudi, UAE, Jordan, Oman, Syria, Yemen, Kuwait, Egypt, Libya, Algeria, Morocco, Tunisia, Tanzania, Sudan, Kenya, Uganda, Ethiopia, Burkina Faso, CZPT elements vfr 800 chain and sprocket established for Honda Ecuador, Columbia, Venezuela, Peru, Brazil, Chile, Uruguay, Argentina, Xihu (West Lake) Dis.via, Malaysia, Indonesia, Vietnam, Thailand, Srilanka, and so on more than 70 nations.KTA series shaft mounted gearbox(velocity reducer) with helical hardened gears has the attributes of large carrying ability, easy transmission, mild excess weight, reduced energy intake and so on. Enter shaft of KTA pace reducer is linked with equipment motor by belt pulley, hollow output shaft is linked with a essential. It can be replaced by electric powered drum as electrical power for belt conveyors and lifting equipments. KTA sequence shaft mounted gearbox could be connected with back again-cease to avoid the working equipment again skating, and conveniently mounted by tie rod. KTA collection shaft mounted speed reducer is extensively utilized in the mining equipments, concrete mixing batching plant, stone crushers, sand generating generation line and other belt conveyors, mechanical transmission areas.Mechanical belt conveyors travel method is composed of KTA shaft mounted speed reducer, torque arm, pulleys and equipment motors, whose power transmission from the gear motor to the gearbox by means of the pulley, and then velocity reducer passed to the drive pulley via the hollow output shaft and the gearbox is fixed by torque arm, anti-slip device can be configured. The technique is convenient to set up,use and keep. FAQ >>> one. What can we buy from you?Conveyor belt, roller, display mesh, crusher spares, all sorts of CZPT transmission elementstwo. What about the lead time?one) 2–3 times for sampletwo) 20–30 days for mass creation. If urgent,we have environmentally friendly channel.3. Do you have any MOQ limit for orders?Lower MOQ, 50m for conveyor belt/10pc for rollersfour. Is it Okay to print my brand on product?Yes. Please inform us your logo or design and style ahead of mass creationfive. How to promise your good quality?We are 1 of the leading suppliers of Global popular mining company above a long time. Excellent top quality is properly recognized.

worm reducer

Worm reducer gearbox – What You Need to Know

When shopping for a Worm reducer gearbox, it is important to consider the functions and features of the unit. It is also important to take into account its cost. We will take a look at the different types of worm reducer gearboxes and the applications that they can be used for. This will help you choose the right unit for your application.

Features

Worm gears are popular in instruments that require fast stopping, such as elevators and lifts. Their soft materials allow them to absorb shock, which reduces the likelihood of failure. They are also beneficial in heavy-duty machines, such as rock crushers. Some manufacturers offer special worms with zero backlash and high-accuracy reduction.The worm reducer gearbox has a variety of features, including an axial pitch and a circular pitch. The axial pitch of the worm must match the circular pitch of the larger gear. Its threads are left or right-handed, and its lead angle is the distance a point on the thread travels during a revolution of the worm.The worm gear reducer gearbox is widely available, and gear manufacturers typically maintain a large inventory of them. Because worm gears are standardized, their mounting dimensions are generally uniform across manufacturers. This means that choosing one will not require you to change the height, length, or diameter of the output shaft. Worm gear reducer gearboxes also have dimensional consistency.Worm gears are very efficient. They have a high load capacity and a low friction coefficient. The worm gears also have a precise tooth profile, which reduces speed fluctuations and allows for quiet operation.

Functions

Worm gears have different functions. They can be used in a variety of applications. For instance, they can be used in elevators to reduce the load on the elevator. These gears also have low noise levels because they are made of dissimilar metals. Moreover, these gears can be used in elevators because they are suitable for this type of application. However, they need a single stage reducer gearbox to function properly.Another important feature of a worm reducer gearbox is that it can operate in reverse. This means that the input shaft turns backwards, while the output shaft rotates forwards. Examples of such applications include hand-cranked centrifuges, blacksmithing forge blowers, and the wind governor of musical boxes. Worm gears are available in different shapes and sizes, from gearsets to housed units. They can also be configured as multi-speed designs. Some manufacturers also offer special precision and zero-backlash worms.A worm reducer gearbox’s tooth form is important in determining the capacity of the device. Typically, a single-lead worm gear has the same lead on the left and right tooth surfaces, although a dual-lead worm gear has different leads on each side. This feature helps to eliminate play in the worm gear. However, it is important to note that a worm reducer gearbox can be manufactured with different tooth shapes for different applications.The worm gear is an alternative to conventional gears. It operates in a similar fashion to ordinary gear drives. The main advantage of a worm gear is that it is able to reduce the rotational speed and torque of a rotating shaft. It also has the added benefit of being able to transfer motion at an angle of 90 degrees. The only drawback of a worm gear is that it cannot reverse motion.

Applications

This market report analyzes the Worm reducer gearbox market from a global perspective. It includes a comprehensive analysis of the current market trends and future growth prospects. It also provides information about the competitive landscape and the main players in the industry. The report also highlights the key factors affecting the growth of the Worm reducer gearbox market.
The major regional markets for the Worm reducer gearbox include North America, Asia-Pacific, the Middle East and Africa, Latin America, and Europe. The market in these regions is likely to remain stable with a limited growth over the next few years. A worm gear is a small mechanical device that is connected to a larger gear. When connected together, it produces a low output speed but high torque.The gearing on a worm drive can be right-hand or left-hand, and can turn clockwise or counter-clockwise. Depending on the worm’s helix angles, back-driving and friction can be reduced. Worm gears are available in housed units or in gearsets. Some manufacturers offer integrated servomotors and multi-speed designs. High-accuracy and zero-backlash worms are available.Worm gears are particularly popular in instruments that require fast stops. They are also commonly found in elevators and lifts. Their soft nature and low-shock characteristics make them highly suitable for these types of machines.
worm reducer

Cost

Cost is an important consideration when selecting a worm reducer gearbox. The initial cost of a worm gear reducer gearbox is considerably lower than other types of gear reducer gearboxes. Worm gear reducer gearboxes are also more energy-efficient, and have higher overload capacities than competitive systems. The following are factors that affect the cost of a worm gear reducer gearbox.Stainless steel worm gear reducer gearboxes from Agknx offer great value for the money. They offer flange input and hollow output bore sizes, as well as center distances ranging from 1.75″ to 3.25″. In addition to the standard version, a stainless steel bushing kit is available, which allows users to use a wider range of head shaft sizes. Stainless steel worm gear reducer gearboxes are available in stock from all six of Agknx’s regional warehouses. They also come with free prepaid freight.Worm gear reducer gearboxes are often used in power transmission systems, elevators, conveyor belts, and medical equipment. In these applications, they are used to control the speed of a load and prevent it from freefall. While worm gear reducer gearboxes are not as efficient as helical gearboxes, they are still very useful for applications that require high torque or high output rates.To select the right type of worm for your application, you should consider the number of teeth it contains. It’s best to select worms with a combined total of 40 teeth or more.

aspect

Worm reducer gearboxes vary in size. They have one, two or more threads. Each thread has a lead angle. A high ratio has more teeth than a low gear, and a low ratio has fewer teeth. These differences are the result of gearing. The size of the worm gear reducer gearbox should be selected according to the specific application.The worm gear reducer gearbox saves space and provides more torque. Agknx Gearbox has created a variety of models to overcome common deceleration challenges, from standard to hygienic markets. The superior transmission Agknx range is designed to solve common deceleration challenges and expand to meet the needs of the sanitary industry.The diameter of the worm reducer gearbox is an important consideration. Its diameter should be equal to or slightly larger than the diameter of the grinding wheel or tool. This will affect the pressure angle. The pressure angle on a worm reducer gearbox depends on several factors, including its diameter and lead angle. The diameter of the grinding wheel or tool also has an effect on the profile of the worm.Worm gear reducer gearboxes are common. Many gear manufacturers have large stocks of these gear reducer gearboxes. Since gears are standardized, the mounting dimensions of worm gears are also common among manufacturers. This makes it easy to select a worm gear reducer gearbox for your application. In addition, the worm gear reducer gearbox is easy to install and maintain.
worm reducer

Worm gear reducer gearbox oil

Worm gear reducer gearboxes usually use gear oil. Several types of gear oils are available, including synthetic, polyalkylene glycol, and mineral oils. The oil used in the worm gear reducer gearbox must have the right viscosity for the gear. Some oils are more corrosive than others and should be avoided if the environment is toxic.The oil of the worm gear reducer gearbox must be protected against corrosion, wear and friction. It is best to choose a lubricant with low friction rate, high oxidation resistance and good anti-wear protection. While mineral oils are the most common type of lubricant, synthetic base oils can improve gear efficiency and reduce operating temperatures. This is because the Arrhenius rate rule states that the chemical reaction in the oil doubles for every 10 degrees Celsius increase in temperature.Worm gear reducer gearboxes are available in a variety of sizes and configurations. They are suitable for all kinds of machines and equipment. The sliding action between the worm gear and the output shaft produces high torque and high efficiency. If the transmission speed is low, the worm gear and output shaft can be combined for maximum efficiency.Worm gear reducer gearboxes require less frequent oil changes than other types of gear reducer gearboxes. However, regular oil should be changed every six months or 2,500 hours, whichever comes first. Also, it is a good idea to regularly monitor the oil level to prevent lubrication-related gearbox failures. It’s also wise to use synthetic oil, as it will last longer between oil changes.

China 150 ratio speed reducer gearbox helical worm geared motors s series speed reducer gear box assembly with reducer gear box     aluminum worm gearboxChina 150 ratio speed reducer gearbox helical worm geared motors s series speed reducer gear box assembly with reducer gear box     aluminum worm gearbox
editor by Cx 2023-06-29

China 1400rpm Helical Gear Reducer,High Speed And Low Noise Nmrv Series Worm Gear Motor, NMRV 90 Gearboxes With Electric Motor cone drive worm gearbox

2023-06-16

China Standard F Series Parallel Shaft Helical Gearboxes for Cranes worm gearbox design

Product Description

 

Product Description

Product Description

-F Series Parallel Shaft Helical gearbox

 

Product Features

1. Modular design, compact structure. Extra-slim parallel shaft helical gearmotors are the perfect solution when space is limited     
2. F series parallel shaft helical gearmotors are typically used in conveyors and materials processing applications      
3. Multi-stage (2 or 3 stages) gear units for low output speed     
4. Hollow output shaft with keyed connection, shrink disk, splined hollow shaft, or torque arm
5. Can be combined with other types of gearboxes (Such as R Series, UDL Series)    
6. Optional mounting options (foot-mounted, flange-mounted, shaft-mounted)    

 

 

 

Product Parameters

 

Models Output Shaft Dia. Input Shaft Dia. Power(kW) Ratio Max. Torque(Nm)
Solid Shaft Hollow Shaft
F38 25mm 30mm 16mm 0.18~3.0 3.81~128.51 200
F48 30mm 35mm 16mm 0.18~3.0 5.06~189.39 400
F58 35mm 40mm 19mm 0.18~5.5 5.18~199.70 600
F68 40mm 40mm 19mm 0.18~5.5 4.21~228.99 820
F78 50mm 50mm 24mm 0.37~11 4.30~281.71 1500
F88 60mm 60mm 28mm 0.75~22 4.20~271.92 3000
F98 70mm 70mm 38mm 1.1~30 4.68~276.64 4300
F108 90mm 90mm 42mm 2.2~45 6.20~255.25 7840
F128 110mm 100mm 55mm 7.5~90 4.63~172.33 12000
F158 120mm 120mm 70mm 11~200 12.07~270.18 18000

 

Materials Data Sheet

Housing material

Grey Cast iron

Housing hardness

HBS163~255

Gear material

20CrMnTi alloy steel

Surface hardness of gears

HRC58°~62 °

Gear core hardness

HRC33~48

Input / Output shaft material

40Cr alloy steel

Input / Output shaft hardness

HRC32~36

Machining precision of gears

accurate grinding, 6~5 Grade

Lubricating oil

GB L-CKC220-460, Shell Omala220-460

Heat treatment

tempering, cementiting, quenching, normalizing, etc.

Efficiency

94%~96% (depends on the transmission stage)

Noise (MAX)

60~68dB

Temp. rise (MAX)

40°C

Temp. rise (Oil)(MAX)

50°C

Vibration

≤20µm

Backlash

≤20Arcmin

Brand of bearings

China top brand bearing, HRB/LYC/ZWZ/C&U. Or other brands requested, SKF, FAG, INA, NSK.

Brand of oil seal

NAK — ZheJiang or other brands requested

Detailed Photos

Our process of production

 

 

Our product line

 

Company Profile

Company Profile

Bode was founded in 2007, which is located in HangZhou city, ZHangZhoug province. As 1 professional manufacturer and exporter, we have more than 17 years’ experience in R & D of worm reducer, gear reducer, gearbox , AC motor and relative spare parts. We have factory with advanced production and test equipment, the strong development of team and producing capacity offer our customers with high quality products. Our products widely served to various industries of Metallurgy, Chemicals, lifting, mining, Petroleum, textile, medicine, wooden etc. Main markets: China, Africa, Australia, Vietnam, Turkey, Japan, Korea, Philippines… Welcome to ask us any questions, good offer always for you for long term business.

FAQ

Q1: Are you trading company or manufacturer?
A: We are factory.

Q2: What kinds of gearbox can you produce for us?
A: Main products of our company: R, S, K, F series helical-tooth reducer, RV series worm gear reducer,H Series Parallel Shaft Helical Reduction Gear Box

Q3: Can you make as per custom drawing?
A: Yes, we offer customized service for customers.

Q4: Can we buy 1 pc of each item for quality testing?
A: Yes, we are glad to accept trial order for quality testing.

Q5: What information shall we give before placing a purchase order?
A:  a) Type of the gearbox, ratio, input and output type, input flange, mounting position, and motor informationetc.
     b) Housing color.
     c) Purchase quantity.
     d) Other special requirements.

Q6: How long is your delivery time?
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock.

Q7: What is your terms of payment ?
A: 30% Advance payment by T/T after signing the contract.70% before delivery

Dear customers,  If you are interested in our product, welcome to contact with us.
Our team will do our best to meet your need 🙂 

 

Application: Machinery, Marine, Agricultural Machinery
Function: Distribution Power, Change Drive Torque, Speed Changing, Speed Reduction
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Vertical Type
Step: Single-Step
Samples:
US$ 50/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

worm reducer

What is a worm gear reducer gearbox?

The worm gear reducer gearbox is used to change the output speed of the mechanical device. It consists of worm and helical gears mounted on the input side of the equipment. In some cases, this gear reduction system can be multi-stage, enabling extremely low output speeds. It has the advantages of low energy consumption and low vibration.
Hollow shaft worm gear reducer gearbox

Worm gear reducer gearbox is an effective device to reduce the speed of mechanical equipment. The use of hard steel or non-ferrous metals for the worm increases its efficiency. Worms made of hard steel generate more heat than worms made of mild steel. Different thermal expansion results in gaps between mating surfaces. Despite its many benefits, worm gear reducer gearboxes are prone to oil leakage, which can be a problem for a number of reasons.
Hollow shaft worm gear reducer gearboxes are available in different gear ratios and are compatible with many motor types. Some are available in dual-axis and single-axis configurations and can be mounted horizontally or vertically. They are also available in intermediate ratios, as well as four- and five-speed transmission types. They can also be connected with additional output shafts.
Another type of worm gear reducer gearbox is the multi-stage variety. This gear reducer gearbox has multiple stages, enabling it to reduce speed with extremely low output speeds. In addition to the large transmission ratio, the multi-stage gear reducer gearbox has low noise, low vibration and low energy consumption.
Worm gear reducer gearboxes offer space-saving solutions as well as increased torque. Agknx Gearbox offers worm gear reducer gearboxes that solve common deceleration problems. The company has also expanded its product range into the bathroom market. Compared with the standard gearbox, the worm gear reducer gearbox has the characteristics of lower price and better torque output.
Agknx worm gear

The Agknx type worm gear reducer gearbox has multi-tooth line contact and is widely used in heavy machinery. These gears are characterized by a high load-carrying capacity, but they are highly sensitive to misalignment and manufacturing errors. However, by employing point contact, these gears can be made more reliable and can withstand higher loads.
Another major advantage of the Agknx worm gear is its high load capacity. The tooth profile design of the gears has a high relative slip ratio, which improves efficiency and load capacity. In addition, the large angle between the sliding direction and the contact line provides a low coefficient of friction. The Agknx worm gear also features premium carburized steel and phosphor bronze castings for exceptional durability. In addition, the tooth profile is very precise, the operation is quiet, and the speed fluctuation is small.
Agknx worm gear reducer gearboxes are designed to operate for up to ten hours per day with an even load. The design of this worm gear reducer gearbox stems from Sumitomo Heavy Industries’ extensive experience in gear reducer gearboxes. The smooth surface texture and precise tooth profile of the gears ensure that the gears can withstand high loads without damaging the lubricant film. In addition, Agknx worm shafts are specially designed to have the right stiffness.
Agknx worm gear reducer gearboxes are designed to maximize load capacity while minimizing energy consumption. Its fully meshed teeth reduce surface pressure on the worm gear teeth and increase load capacity.
worm reducerDouble throat worm gear

There are a few things to consider when choosing a dual-throat worm gear. First, the diameter of the root circle must match the circle pitch of the larger gear. This measurement is usually done by measuring the distance between adjacent teeth. Alternatively, the worm’s normal module can be used. It is the value entered in the worm module dialog. In addition, the axial pitch of the worm should be equal to the pitch diameter of the circular pitch.
Double-throat worm gears are an excellent choice for heavy and heavy-duty applications. The design of this worm gear is ideal for heavy-duty applications as it provides a tighter connection between the worm and the gear. It is also more compact than other types of gear and is comparable to a fine-pitch lead screw.
The efficiency of a double-throat worm gear depends on the material of the gear and worm. Typically, gears are made of case-hardened steel, while worm gears are made of bronze or cast iron. In some cases, a combination of cast iron and bronze can be used.
The deflection of the worm shaft is also affected by the tooth parameters. Tooth height, pressure angle, and size factors all affect the deflection of the worm shaft. In addition, the number of worm threads is another important parameter that affects the deflection of the worm shaft.
Double-throat worm gears are commonly used in industrial applications where high drive reduction is required. The worm has a concave and internal tooth structure that can be adjusted to achieve various ratios. Worm gears and worm gear assemblies must be properly mounted on their shafts to prevent back drive.
Brass worm gear

The basic working principle of the brass worm gear reducer gearbox is the same as that of the traditional worm gear reducer gearbox. Its axial pitch must be equal to the circumferential pitch of the larger gear. The single-thread design advances one tooth per revolution, while the double-thread design advances two teeth. The threads on the worm are either left-handed or right-handed. The lead of a worm is the distance a point on the thread of the worm moves in one revolution. The lead angle is the angle tangent to the pitch of the cylinder and the axis of the worm.
Double-thread worm gear reducer gearboxes are best for heavy loads. It provides the tightest connection between the worm and the gear. Assembly of the worm gear requires precise mounting. The keyway installation method involves drilling a square cut in the gear hole. This prevents the worm from rotating on the shaft and helps transmit torque. Then use the set screw to secure the gear to the hub.
The large fuel tank helps keep the worm gear clean and reduces heat. It also provides lubrication for extended life. Worm gear reducer gearboxes with oil reservoirs provide a lubricated environment and low-friction surfaces. Additionally, it offers multi-position installation flexibility. Additionally, its housing is cross-milled for precise alignment. It also features internal baffles for leak-free ventilation.
I260 series worm gear reducer gearboxes are one-piece iron casings with solid or hollow output shafts and tapered roller bearings. This gear reducer gearbox is designed for low to medium-horsepower applications. This gear reducer gearbox is a cost-effective option with low initial cost, the high gear ratio, and high torque in a compact package. Also, it is more shock resistant than other gear reducer gearboxes.
worm reducerBrass worm gear

Brass worm gear reducer gearbox is a reduction gear. This type of gear can provide a lot of reduction in a small package. This type of gear reducer gearbox also has the ability to generate high torque. However, it is important to understand that this gear reducer gearbox has thermal limitations, which reduce its efficiency. The choice of lubricant for this gear reducer gearbox is very flexible. However, being a yellow metal, it is important to remember that the lubricant must be non-reactive.
Worm gears are used in many consumer and industrial applications and have high reduction ratios. These gears are produced in various configurations and sizes. Worm gears are similar to spur gears but have non-parallel shafts. Worm gears are also suitable for applications requiring low output speed but high torque.
Worm gears have some distinct advantages over other gears. First, unlike standard gears, the worm rotates in a worm-like motion. This mechanism prevents reverse movement. This is because the lead angle of the worm gear is small. Additionally, the worms self-lock, helping to prevent reversal. However, this mechanism is not entirely reliable. Worm gears can be found in elevators, fishing reels, sprockets, and automotive power steering.
Another advantage of worm gears is that they are easy to manufacture. The rationale behind this design is to have two mutually perpendicular axes. Then, two or more threads are added to the worm gear. The common tangent between these two shafts intersects the pitch line of the worm gear shaft. This is the basis of transfer speed.

China Standard F Series Parallel Shaft Helical Gearboxes for Cranes   worm gearbox designChina Standard F Series Parallel Shaft Helical Gearboxes for Cranes   worm gearbox design
editor by CX 2023-05-30

China Custom Cast Iron Material Helical Worm Gearbox for Power Transmission Industrial Machines manufacturer

Merchandise Description

 

Merchandise Description

 

Merchandise Description

-S Sequence Helical gearbox
 

 

Merchandise Attributes
1.Higher modular design.
2.Integrated casting housing,compact dimension,large loading help, secure transmitting and lower sounds degree.
three.With the particular gear geometry, it will get higher torque, performance and long existence circle.
4.It can obtain the immediate combination for 2 sets of gearbox.
5.Large efficiency and save power.

6.Save expense and minimal upkeep.

 

Solution Parameters

one. Technical data

Measurement 38 48 58 sixty eight 78 88 ninety eight
Framework BS   BSA   BSF   BSAF   BSAT   BSAZ
Input Power(kW) .eighteen~.seventy five .eighteen~1.five .18~3 .twenty five~5.5 .55~7.five .seventy five~15 one.5~22
Ratio ten.27~one hundred sixty five.seventy one 11.forty six~244.seventy four 10.78~196.21 eleven.55~227.20 nine.96~241.09 11.83~223.26 12.75~230.48
Permissible Torque(N.m) 90 a hundred and seventy 300 520 1270 2280 4000
Bodyweight(kg) 7 ten fourteen 26 fifty one hundred 170

2: Layout alternative
 

S series gear units are available in the following designs
S…Y… Foot-mounted parallel shaft helical gear units with solid shaft
SA…Y… Parallel shaft helical gear units with hollow shaft
SAZ…Y… Brief-flange mounted parallel shaft helical gear units with hollow shaft
SF…Y… Flange-mounted parallel shaft helical gear units with solid shaft
SAT…Y… Flange-mounted parallel shaft helical gear units with hollow shaft
S(SF,SA,SAF,SAZ)S… Shaft input parallel shaft helical gear units
S(SF,SA,SAF,SAZ)…R…Y… Combinatorial parallel shaft helical gear units
S(SF,SA,SAF,SAZ)S…R… Shaft input combinatorial parallel shaft helical gear units

 

Supplies Info Sheet

Housing material

Gray Solid iron

Housing hardness

HBS163~255

Equipment content

20CrMnTi alloy metal

Floor hardness of gears

HRC58°~sixty two °

Gear main hardness

HRC33~48

Enter / Output shaft substance

40Cr alloy metal

Enter / Output shaft hardness

HRC32~36

Machining precision of gears

accurate grinding, 6~5 Quality

Lubricating oil

GB L-CKC220-460, Shell Omala220-460

Warmth remedy

tempering, cementiting, quenching, normalizing, and so on.

Performance

94%~96% (relies upon on the transmission stage)

Sounds (MAX)

sixty~68dB

Temp. rise (MAX)

40°C

Temp. increase (Oil)(MAX)

50°C

Vibration

≤20µm

Backlash

≤20Arcmin

Model of bearings

China top brand name bearing, HRB/LYC/ZWZ/C&U. Or other brand names asked for, SKF, FAG, INA, NSK.

Brand of oil seal

NAK — ZheJiang or other brand names asked for

 

In depth Photos

 

 

Our method of manufacturing

 

 

Our item line

 

 

Firm Profile

 

Organization Profile

Bode  was launched in 2007, which is situated in HangZhou metropolis, ZHangZhoug province. As 1 expert manufacturer and exporter, we have far more than seventeen years’ knowledge in R & D of worm reducer, gear reducer, gearbox , AC motor and relative spare parts. We have manufacturing unit with superior creation and test products, the powerful development of group and creating potential offer our clients with substantial high quality products. Our items broadly served to a variety of industries of Metallurgy, Chemicals, lifting, mining, Petroleum, textile, medication, picket etc. Main marketplaces: China, Africa, Australia, Vietnam, Turkey, Japan, Korea, Philippines… Welcome to request us any inquiries, good offer you always for you for long phrase enterprise.

FAQ

Q1: Are you buying and selling company or producer?
A: We are manufacturing facility.

Q2: What kinds of gearbox can you produce for us?
A: Primary goods of our organization: R, S, K, F collection helical-tooth reducer, RV sequence worm equipment reducer,H Sequence Parallel Shaft Helical Reduction Gear Box

Q3: Can you make as for each custom made drawing?
A: Of course, we offer custom-made provider for customers.

Q4: Can we acquire 1 computer of every single product for high quality tests?
A: Indeed, we are happy to settle for demo purchase for quality screening.

Q5: What details shall we give just before inserting a acquire buy?
A:  a) Variety of the gearbox, ratio, input and output sort, input flange, mounting position, and motor informationetc.
     b) Housing coloration.
     c) Buy quantity.
     d) Other special needs.

Q6: How lengthy is your delivery time?
A: Generally it is 5-10 days if the items are in inventory. or it is 15-twenty times if the products are not in inventory.

Q7: What is your terms of payment ?
A: thirty% Progress payment by T/T soon after signing the contract.70% before shipping

If you are fascinated in our merchandise, welcome to make contact with with us.
Our team will do our best to meet your need 🙂 
 

 

Application: Motor, Machinery, Marine, Agricultural Machinery
Function: Distribution Power, Change Drive Torque, Speed Changing, Speed Reduction
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Step: Double-Step
Samples:
US$ 90/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|